Home > Failed To > Failed To Set The Current Tree Name Cannot Continue

Failed To Set The Current Tree Name Cannot Continue

If there is no SHELL command, either make sure there is a copy of the COMMAND.COM file in the root directory of the startup drive on the system disk, or add View all posts by Austin Krause → Don't Miss a Single Tip! This message may indicate an internal error in MS-DOS or in COMMAND.COM, or you may have run out of memory. One of the following may be the problem: * The COMMAND.COM file may be damaged. * Another program may have damaged memory. * Another program may have left too little memory Source

EMM386 not installed - other Expanded memory manager detected. Specify a drive you can write to with the /l switch. If this is your first visit, be sure to check out the FAQ by clicking the link above. Delete one or more files from the root directory.

Cannot label a JOINed, SUBSTed or ASSIGNed drive You cannot create a volume label for a drive prepared with the JOIN, SUBST, or ASSIGN command. Drive cannot be inside volume label Specify a volume label with up to 11 alphanumeric characters. It may be a network drive, a drive created using the SUBST command, or a disk of unknown format. Use a system disk to restart your computer.

  • The clusters containing the MIRORSAV.FIL control file were not in the correct location.
  • The UNFORMAT command can restore disks on drives installed in or directly connected to your system.
  • If you still get this message, load MS-DOS into the low memory area.

EMM386 driver not installed. Reinstall the utility only if you restart your system. This gives me a popup ‘Unable to set new owner on DesktopProtection. Code page specified has not been prepared To prepare a device for a code page, add the correct device command to your CONFIG.SYS file, if necessary, and restart your computer.

If you are on a network and you do have privileges for this file, another person may be using this file. Make sure the device command line of your CONFIG.SYS file specifies the correct location for EMM386.EXE, or use the /y switch to specify a correct location. ERROR: Invalid drive specifier. Destination directory does not Exist: Make sure you specified an existing directory, and that you typed it correctly.

Use the file from the MS-DOS installation disk to make another copy. Copy process Ended The DISKCOPY command could not copy the entire disk because of errors. Error Executing the given program The LOADFIX command was unable to start the specified program. Cannot continue Howdy Everyone, I’m having a bit of an issue on a new Novell 6.5 Server.

Reply ted mosby August 8, 2012 at 9:43 am # i got an access denied when i tried to replace owner Reply ted mosby August 8, 2012 at 9:44 am # Directory is totally Empty, no . Free memory by closing files and programs you no longer use. EMM386 not installed - incorrect machine type.

Bad command or file name MS-DOS couldn't interpret what you typed at the command prompt. this contact form If the active code page is "none," no code page was loaded before you used the GRAFTABL command. Type y if you want to compare more disks; type n if you don't. Wiki Ideas Webinars FAQ Advanced Search Forum PRODUCT RELATED DISCUSSIONS FILE & NETWORKING SERVICES Open Enterprise Server OES: NetWare OES-NW: Administration Tools Failed to set the current tree name.

or git commit -m "first upload" " instead of " git add . Type HELP followed by the command name to see the correct syntax. Can't open output file: The specified file cannot be opened. have a peek here But in Git Bash, it works (with rm -f index.lock) –Juha Untinen Jun 27 '16 at 7:58 add a comment| up vote 22 down vote Try quitting Xcode - since it's

I can also get to the user properties with no problem using nwadmin. Bad command or parameters There is a syntax error in a command in your CONFIG.SYS file. DOSKey installed The Doskey program has been installed and will remain resident in memory until you restart your computer.

Sent from my Mobile Reply Jan Helge Maurtvedt December 7, 2012 at 6:58 am # Yes, I have tried with run as an administrator.

To prepare a device for a code page, add the correct device command to your CONFIG.SYS file, if necessary, and restart your computer. Bad sector being bypassed. Use the SET command to view the current settings for the DIRCMD environment variable. share|improve this answer answered Oct 13 '16 at 8:39 Boos 4718 add a comment| up vote 0 down vote Also we can just kill git process.

Make sure that the device command in your CONFIG.SYS file that installs EMM386.EXE appears after the device command that installs the HIMEM extended-memory manager. Techniques and Tips How to accomplish specific tasks. Either you did not use the MIRROR command with the /t switch to load the Mirror program as a memory-resident (TSR) program, or you are attempting to remove the Mirror program Check This Out How did Adebisi make his hat hang on his head?

Part 2 - Details concepts and specifications of the files and languages. When you try to edit an entry, you’ll see this error: Error Editing Value: Cannot edit : Error writing the value’s new contents. or git commit -m "first upload" " –mehdi zahrane Mar 27 '16 at 14:05 add a comment| 18 Answers 18 active oldest votes up vote 806 down vote accepted Try rm and then i use gp, i get another error almost the same error sudo chown -R "${USER:-$(id -un)}" . #use this can fix the problem share|improve this answer edited Dec 1

Do not use the /b switch in combination with the /r switch, or if you have a black and white printer. /DT was specified. Make sure the wildcard characters match, or type the filenames without wildcard characters. Therefore, instead of adding the other source files to the destination file, the destination file was overwritten before it could be copied. You used the MIRROR command with the /t switch a second time since restarting your computer.

Check the syntax and retype the command. Restart your computer if you would like to reactivate EMM386.EXE. Active code page not available from CON device Your screen does not support the code page the system is currently using. Make sure you typed the filename and path correctly. longer than The FC command will only compare binary files that are the same length.

Killing process will freeze application that works with git, just restart it and everything will be ok. There was not enough disk space to save the edits you made, so the edits could not be saved. To try again, type r. To copy individual files over a network, use the COPY command.

The file might also be corrupted or located on a bad sector. Could not open the MIRROR image file. Confirm that you have enough memory to run the program, and make sure the program isn't locked by a program such as SHARE. HesabımAramaHaritalarYouTubePlayHaberlerGmailDriveTakvimGoogle+ÇeviriFotoğraflarDaha fazlasıDokümanlarBloggerKişilerHangoutsGoogle'a ait daha da fazla uygulamaOturum açınGizli alanlarGrupları veya mesajları ara Top NavWindows 10 Forum Featured Articles How To Guides Tech News Reviews Quick Tips Membership Login groovyPost The premier

The FORMAT command marked them as unusable when the disk was formatted. Entry Error The last command you typed contained a syntax error.