Sign In Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password? This is 15.7.11 with LibreSSL.SUPERMICRO MBD-X9SBAA-F-O http://www.supermicro.com/products/motherboard/ATOM/X9/X9SBAA-F.cfm8GB ECC RAM120GB SSDIntel PWLA8492MT PRO/1000 MT http://www.intel.com/content/www/us/en/ethernet-products/gigabit-server-adapters/pro-1000-mt-dp.htmlI'm not sure how to diagnose. Re: 3ware 9650SE bad disk performance LucasAlbers Sep 19, 2009 8:59 AM (in response to vsu) What are your cache settings set to? Share this post Link to post Share on other sites jpiszcz 1 Member Member 1 576 posts Posted August 31, 2010 · Report post Per my earlier message, both cards his comment is here
You can skip to the end and leave a response. Aug 20 17:23:04 jam kernel: [11827.976071] sd 0:0:0:1: WARNING: (0x06:0x002C): Command (0x8a) timed out, resetting card. What is your queue_depth set to? Share this post Link to post Share on other sites jpiszcz 1 Member Member 1 576 posts Posted August 31, 2010 · Report post Hi, What kernel are you running?
If you google that exact error, there is very little information, if I findsomething that works, I'll update the list so others have something to point to when they see this With MD raid, mkfs.xfs optimizes automatically, but for HW RAID, I did not notice any improvement whether the optimized parameters were used or not. the related kernel messages are : sd 0:0:0:0: WARNING: (0×06:0×002C): Command (0×28) timed out, resetting card. 3w-9xxx: scsi0: WARNING: (0×06:0×0037): Character ioctl (0×108) timed out, reset ting card. I've read about nr_requests vs queue_depth before and everything I've seen (1, 2) says that the queue_depth should be half of nr_requests. 3ware defaults to TW_Q_LENGTH(256)-2, but the default nr_requests is
Logged russoj88 Newbie Posts: 10 Karma: 1 Re: Watchdog timeout -- resetting « Reply #9 on: September 04, 2015, 02:01:54 AM » Quote from: Solaris17 on September 01, 2015, 04:23:54 AMGood Thanks for the info. http://marc.info/?l=linux-kernel&m=127419418304483&w=2 Adam Radford (2): 3ware maintainers update 3w-xxxx, 3w-9xxx: force 60 second timeout I will go back to 2.6.34 and see if the problems persists. The heatsink on the CPU was cool.
Also (in regard to what I was saying earlier about stripe size), the the addendum for 9.5.2 says support for 256KB stripe size on raid6 was added and that it was Even the power regulators for your CPU are rated far above what you can physically touch. How? Thanks, Reply With Quote 0 01-07-2012,04:02 PM #2 SolidJoe View Profile View Forum Posts View Forum Threads I LOVE Cogent!
xfs_info gives me; ... This would be alot easier if I didn't have my root on the array... Share this post Link to post Share on other sites superlgn 0 Member Member 0 118 posts Posted August 30, 2010 · Report post 2009-WARNING - Verify fixed data/parity mismatch: Logged Hobbyist at home, sysadmin at work.
kernel: 3w-9xxx: scsi0: WARNING: (0x06:0x0037): Character ioctl (0x108) timed out, resetting card. this content Aug 23 10:14:44 jam kernel: [222366.132048] 3w-9xxx: scsi0: AEN: INFO (0x04:0x005E): Cache synchronization completed:unit=0. The root filesystem is on a separate RAID-1 4 port card (also w/BBU). It's been about a week... 2.
I've had my occasional read/write resets going all the way back to October 2009, when I was probably using Unstable Debian with 2.6.31 or .32. but im actually very good with hardware if BSD is indicating watchdog errors than the fault may actually lie with the overall system stability. Member Posts: 373 Karma: 39 Re: Watchdog timeout -- resetting « Reply #5 on: August 31, 2015, 09:07:59 PM » I have a similar type case, except backwards.Superserver with a Atom Re: 3ware 9650SE bad disk performance salmonj Oct 2, 2009 5:01 AM (in response to tijuhasz) Just out of curiousity, what kind of RAID setup you experiencing this on and what
Also (in regard to what I was saying earlier about stripe size), the the addendum for 9.5.2 says support for 256KB stripe size on raid6 was added and that it was syslog:Aug 26 21:05:22 p34 kernel: [462727.945313] 3w-9xxx: scsi0: WARNING: (0x06:0x0037): Character ioctl (0x108) timed out, resetting card. It's easy! check over here You need to set the ESSID to the same value on all cards including the AP (if any).
One other thing (so its not missed) is the hotswap bays. Well, look at this! [152904.636062] 3w-9xxx: scsi1: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. [152917.721865] 3w-9xxx: scsi1: AEN: INFO (0x04:0x0001): Controller reset occurred:resets=2. I've never seen the "Response queue (large)" or "Controller reset occurred" messages before. I find myself with the same setup. 8x WD2002FYPS with 9650Se-16 port on Ubuntu x64 8.04 (2.6.24-24) and xfs.